Connect problems

Aggcar · **Joined:** Thu Jan 30, 2014 3:03 pm **Posts:** 5

I have problem connect my Dlink DCS930L to CamLan. Have two webcams without connectproblem but can`t get my Dlink-camera connected. Somebody know how to do?
The Dlink-camera is correct functionaling when standalone.

Aggcar

Marc · **Posted:** Thu Jan 30, 2014 3:49 pm

Hello,

please have a look here, for sample camera URLs
http://www.crazypixels.com/support

Please also try to find possible URLs through this site
http://skjm.com/icam/mjpeg_test.php

Aggcar · **Joined:** Thu Jan 30, 2014 3:03 pm **Posts:** 5

Marc wrote:

Hello,

please have a look here, for sample camera URLs
http://www.crazypixels.com/support

Please also try to find possible URLs through this site
http://skjm.com/icam/mjpeg_test.php

Thanks!

I have visit them several times without results. They give 6 different ways to go. I will do another try and hope the best will happen.

Aggcar

Marc · **Posted:** Thu Jan 30, 2014 7:41 pm

If you found a working URL on this site, than you can double check the URL in the address field of your webbrowser.
You should receive an image.

Be aware, that you select in CamUniversal the correct video type (still-picture, mjpeg-stream).

Aggcar · **Joined:** Thu Jan 30, 2014 3:03 pm **Posts:** 5

Marc wrote:

If you found a working URL on this site, than you can double check the URL in the address field of your webbrowser.
You should receive an image.

Be aware, that you select in CamUniversal the correct video type (still-picture, mjpeg-stream).

I have done everything with different ends as .cgi, .mjpg and so on. I get picture when i write URL in webbrowser but can`t get it in CamLan.

Aggcar

Marc · **Posted:** Fri Jan 31, 2014 10:14 am

Is it possible for you to make your camera URL accessible from remote?
If yes, I can access the URL and have a look why there are problems.

Please send me this URL via email if possible.

Aggcar · **Joined:** Thu Jan 30, 2014 3:03 pm **Posts:** 5

Marc wrote:

Is it possible for you to make your camera URL accessible from remote?
If yes, I can access the URL and have a look why there are problems.

Please send me this URL via email if possible.

I did via support email. Have you got it?

Marc · **Posted:** Sat Feb 01, 2014 7:08 pm

Didn't you say, that you forgot the camera authentification?

The URL you sent was not accessible from remote. It was your local intranet URL.
You have to adjust your router, so that your camera URL could be accessed from remote.

Aggcar · **Joined:** Thu Jan 30, 2014 3:03 pm **Posts:** 5

Marc wrote:

Didn't you say, that you forgot the camera authentification?

The URL you sent was not accessible from remote. It was your local intranet URL.
You have to adjust your router, so that your camera URL could be accessed from remote.

I meaned I forgot to send it first time.

I`m sorry, I`m not so good in computerwork. Just now I can`t remember how to do. Age 77.

Thank`s för trying help me.

Aggcar

Marc · **Posted:** Sun Feb 02, 2014 1:00 pm

Ok.

If you get a picture in your webbrowser by inserting a direct URL to your camera
and on this page http://skjm.com/icam/mjpeg_test.php
then you must get a picture also in CamLAN.

I don't know why you didn't get one. So the best way is, that I can access your camera for testing.
But for this, your camera needs to get accessed for remote.
For this you have to give the permission in your router, that the IP of the camera is accessible from remote.
Perhaps you have a look into to manual of the router how to do this.

Additionl please have a look here too.
viewtopic.php?f=3&t=26&hilit=router

CrazyPixels Forum

Connect problems

Who is online